Car Mechanic Simulator 2018: How to Put Oil in the Engine

Finding the Oil Drain Plug in Car Mechanic Simulator 2018

Alright, first things first: you need to drain the old oil․ Where’s the oil drain plug, you ask? Good question! It’s usually located on the bottom of the engine’s oil pan․ Here’s how to find it:

• Get under the car using the inspection camera․
• Look for a bolt on the bottom of the oil pan․ It’s usually a different color than the pan itself․
• If you’re having trouble, use the “Inspect” tool․ It will highlight interactive parts․

Once you’ve spotted it, grab your trusty oil drain pan and position it underneath․ Then, use the appropriate wrench to loosen and remove the plug․ Let that nasty old oil drain completely․ Don’t rush it!

Pro Tip: Always remember to tighten the oil drain plug after draining the oil! You don’t want to forget this step․ Trust me, you’ll regret it․

Removing the Old Oil Filter in Car Mechanic Simulator 2018

Next up: the oil filter․ This little guy is responsible for keeping your engine oil clean․ A dirty filter means dirty oil, and that’s bad news for your engine․ So, let’s get it changed!

Locating the Oil Filter

The oil filter’s location can vary depending on the engine․ However, it’s usually somewhere on the engine block, often near the front or side․ Again, the “Inspect” tool is your friend here․ Use it to highlight the filter․

Removing the Old Filter

You’ll need an oil filter wrench to remove the old filter․ Attach the wrench to the filter and turn it counter-clockwise to loosen it․ Be prepared for a little bit of oil to spill out, so have a rag handy․ Once it’s loose, you can unscrew it the rest of the way by hand․

Installing the New Oil Filter and Adding New Oil in Car Mechanic Simulator 2018

Okay, we’re getting to the good part – putting in the new stuff! Make sure you have the correct type of oil filter and oil for the vehicle you’re working on․ The game will usually tell you what’s required․

Installing the New Oil Filter

Before installing the new filter, lightly lubricate the rubber gasket with fresh oil․ This will help create a good seal․ Then, screw the filter on by hand until it’s snug․ Don’t overtighten it with the wrench – hand-tight is usually enough․

Adding the New Oil

Now for the grand finale: adding the new oil! Locate the oil filler cap on the engine․ It usually has an oil can symbol on it․ Remove the cap and insert a funnel․ Then, carefully pour in the correct amount of oil․ Check the vehicle’s specifications in the game to determine the proper oil capacity․ Don’t overfill it!

• Use the correct type of oil․
• Don’t overfill the engine․
• Check the oil level with the dipstick․

After adding the oil, replace the filler cap and start the engine․ Let it run for a few minutes, then check the oil level with the dipstick․ Add more oil if needed to reach the “full” mark․ And that’s it – you’ve successfully changed the oil!

Interesting Fact: Did you know that regularly changing your oil in Car Mechanic Simulator 2018 (and in real life!) significantly extends the life of your engine? It’s true!

Car Mechanic Simulator 2018: Checking the Oil Level

Checking the oil level is crucial after an oil change, and periodically during gameplay․ It’s super simple and prevents catastrophic engine failure (virtually, of course!)․

How to Check the Oil Level

Locate the dipstick, usually marked with a yellow or orange handle․ Pull it out, wipe it clean with a rag, then reinsert it fully․ Pull it out again and observe the oil level․ It should be between the minimum and maximum marks on the dipstick․

Troubleshooting Oil Change Issues in Car Mechanic Simulator 2018

Sometimes, things don’t go exactly as planned․ Here are a few common issues you might encounter and how to fix them:

• Oil light stays on: Double-check that you’ve added enough oil and that the oil filter is properly installed․
• Engine knocking: This could indicate low oil pressure or the wrong type of oil․ Drain the oil and refill with the correct type․
• Oil leaking: Make sure the oil drain plug and oil filter are tightened properly․

Car Mechanic Simulator 2018: Oil Change Costs and Profits

Let’s talk business! Oil changes are a bread-and-butter service in Car Mechanic Simulator 2018․ Understanding the costs and potential profits is key to running a successful garage․

Calculating Costs

The cost of an oil change depends on the type of oil and filter required for the vehicle․ Keep an eye on the parts prices in the shop and factor that into your service price․

Maximizing Profits

Offer oil changes as part of a larger service package to increase your profits․ For example, you could combine an oil change with a tire rotation or brake inspection․

Q: What happens if I don’t change the oil?

A: In Car Mechanic Simulator 2018, neglecting oil changes leads to engine damage, reduced performance, and ultimately, engine failure․ It’s not pretty (or profitable!)․

Q: Can I use any oil filter?

A: No! You need to use the correct oil filter specified for the vehicle․ Using the wrong filter can damage the engine․

Q: How often should I change the oil?

A: It depends on the vehicle and the type of oil used․ Check the vehicle’s service manual in the game for recommended oil change intervals․

Q: Where do I buy oil and filters?

A: You can purchase oil and filters from the parts store in the game․ Just select the appropriate parts for the vehicle you’re working on․